收藏 分享(赏)

ASTM_D_4350_-_15.pdf

上传人:益****师 文档编号:180704 上传时间:2023-03-04 格式:PDF 页数:5 大小:145.47KB
下载 相关 举报
ASTM_D_4350_-_15.pdf_第1页
第1页 / 共5页
ASTM_D_4350_-_15.pdf_第2页
第2页 / 共5页
ASTM_D_4350_-_15.pdf_第3页
第3页 / 共5页
ASTM_D_4350_-_15.pdf_第4页
第4页 / 共5页
ASTM_D_4350_-_15.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:D435015Standard Test Method forCorrosivity Index of Plastics and Fillers1This standard is issued under the fixed designation D4350;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in pare

2、ntheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope*1.1 This test method is designed for use in obtaining thespecific condu

3、ctance of a water extract of plastics and fillers.The magnitude of this conductance,called the corrosivityindex,is an index of the likelihood that,in a humidatmosphere,metal surfaces in contact with these materials canbe corroded due to galvanic action or direct chemical attack.NOTE1There is no know

4、n ISO equivalent to this standard.1.2 The values stated in SI units are to be regarded asstandard.1.3 This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety and health pr

5、actices and determine the applica-bility of regulatory limitations prior to use.Specific precau-tionary statements are given in Section 7.2.Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD883 Terminology Relating to PlasticsD1193 Specification for Reagent

6、WaterE1 Specification for ASTM Liquid-in-Glass ThermometersE11 Specification for Woven Wire Test Sieve Cloth and TestSievesE145 Specification for Gravity-Convection and Forced-Ventilation OvensE691 Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test MethodE2251 Speci

7、fication for Liquid-in-Glass ASTM Thermom-eters with Low-Hazard Precision Liquids3.Terminology3.1 Definitions of TermsFor definitions of terms used inthis test method associated with plastics issues refer to theterminology contained in Terminology D883.4.Significance and Use4.1 This test method prov

8、ides a means for comparing thecorrosive potential of plastics and fillers in humid atmospheres.4.2 This test method is intended for use in research andevaluation.5.Apparatus5.1 Conductance Bridge,Wheatstone type,with a rangefrom 1 to 250 000-measured resistance,a built-inpotentiometer,a 1000 6 50-cy

9、cles per second oscillator,and asensitive null point indicator.The bridge shall be capable ofmeasuring resistance with an accuracy of 62%.5.2 Conductivity Cell,dip-type,micro,for solutions ofmedium conductance.The cell needs to have a cell constant ofapproximately 1.0 cm1.The borosilicate glass shal

10、l have amaximum outside tube diameter of 12.7 mm,overall length of177.8 mm,chamber inside diameter of 9.5 mm,and chamberdepth of 50.8 mm.35.3 Drill,electric,capable of holding a 10.54-mm drill bit,and rotating at 500-r/min maximum speed.5.4 Mill,such as laboratory Wiley cutting mill or equivalent.5.

11、5 Sieves,standard(alternative)sieve designations 425 m(No.40),and 250 m(No.60)in accordance with Specifica-tion E11.5.6 Analytical Balance,capable of determining mass to thenearest 1.0 mg.5.7 Oven,forced-ventilation type,with uniformity of tem-perature within 61%of the differential between oven and1

12、This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommittee D20.16 on Thermosetting Materi-als.Current edition approved June 1,2015.Published June 2015.Originallyapproved in 1984.Last previous edition approved in 2013 as D4350-13.DOI:1

13、0.1520/D4350-15.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3The sole source of supply of the conductivity cel

14、l(Model No.3403)known tothe committee at this time is Yellow Springs Instrument Co.,Inc.,P.O.Box 279,Yellow Springs,OH 45387.If you are aware of alternative suppliers,please providethis information to ASTM International Headquarters.Your comments will receivecareful consideration at a meeting of the

15、 responsible technical committee,1whichyou may attend.*A Summary of Changes section appears at the end of this standardCopyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 ambient temperature,with a rate of ventilation of 100 to 200 airchanges

16、 per hour,in accordance with Specification E145,TypeIIA.5.8 Thermometer,solid-stem,precision,ASTM No.63C,inaccordance with Specification E1.Temperature measuringdevices with equivalent accuracy and characteristics,such asRTDs and thermistors,are permitted.Additionally,use ofASTM No.S63C in accordance with Specification E2251 isacceptable.5.9 Chemical Glassware:5.9.1 Borosilicate Glass Flask,nominally 1000-mL size,with ground glass stopper.5.9.2 Borosilicate Glass Erlenmeyer Flask,65-mL actualcap

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2