1、Designation:D409719Standard Specification forContact-Molded Glass-Fiber-Reinforced Thermoset ResinCorrosion-Resistant Tanks1This standard is issued under the fixed designation D4097;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the
2、 year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S.Department of Defense.1.Scope1.1 This specification covers cyl
3、indrical tanks fabricated bycontact molding for above-ground vertical installation,tocontain aggressive chemicals at atmospheric pressure,andmade of a commercial-grade polyester or vinyl ester,resin.Included are requirements for materials,properties,design,construction,dimensions,tolerances,workmans
4、hip,and ap-pearance.1.2 This specification does not cover the design of vesselsintended for pressure above atmospheric or under vacuumconditions,except as classified herein,or vessels intended foruse with liquids heated above their flash points.1.3 The values stated in inch-pound units are to be reg
5、ardedas standard.The values given in parentheses are provided forinformation purposes only.1.4Special design consideration shall be given to tankssubject to environmental and/or mechanical forces suchseismic,wind,ice,agitation,or fluid dynamic forces,tooperational service temperatures greater than 1
6、80F(82C)andto tanks with unsupported bottoms.1.5 The following safety hazards caveat pertains only to thetest method portion,Section 11,of this specification:Thisstandard does not purport to address all of the safety concerns,if any,associated with its use.It is the responsibility of the userof this
7、 standard to establish appropriate safety,health,andenvironmental practices and determine the applicability ofregulatory limitations prior to use.NOTE1There is no known ISO equivalent to this standard.1.6 This international standard was developed in accor-dance with internationally recognized princi
8、ples on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2C581 Practice for Determining Chemica
9、l Resistance ofThermosetting Resins Used in Glass-Fiber-ReinforcedStructures Intended for Liquid ServiceC582 Specification for Contact-Molded Reinforced Thermo-setting Plastic(RTP)Laminates for Corrosion-ResistantEquipmentD618 Practice for Conditioning Plastics for TestingD638 Test Method for Tensil
10、e Properties of PlasticsD790 Test Methods for Flexural Properties of Unreinforcedand Reinforced Plastics and Electrical Insulating Materi-alsD883 Terminology Relating to PlasticsD2150 Specification for Woven Roving Glass Fabric forPolyester-Glass Laminates(Withdrawn 1987)3D2583 Test Method for Inden
11、tation Hardness of Rigid Plas-tics by Means of a Barcol ImpressorD2584 Test Method for Ignition Loss of Cured ReinforcedResinsD2996 Specification for Filament-Wound“Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin)PipeD2997 Specification for Centrifugally Cast“Fiberglass”(Glass-Fiber-Reinforce
12、d Thermosetting-Resin)PipeD3892 Practice for Packaging/Packing of PlasticsD4024 Specification for Machine Made“Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin)FlangesD5421 Specification for Contact Molded“Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin)FlangesF412 Terminology Relating
13、to Plastic Piping Systems1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.23 on ReinforcedPlastic Piping Systems and Chemical Equipment.Current edition approved Aug.1,2019.Published August 2019.Originallyapproved in 1
14、982.Last previous edition approved in 2018 as D4097-18.DOI:10.1520/D4097-19.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe AST
15、M website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles
16、 on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 2.2 ANSI Standards:B 16.1 Cast Iron Pipe Flanges and Flanged Fittings,Class25,125,250,and 8004B 16.5 Steel Pipe Flanges,Flanged Valves and Fittings43.Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nologies D883 and F412,unless otherwise indicated.3.2 Definitions
