1、Designation:D100711(Reapproved 2019)Standard Specification forsec-Butyl Alcohol1,2This standard is issued under the fixed designation D1007;the number immediately following the designation indicates the year oforiginal adoption or,in the case of revision,the year of last revision.A number in parenth
2、eses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers sec-butyl alcohol for use inpaint,varnish,lacquer,and related products.1.2 The values stated in SI units are to be regarded asstan
3、dard.No other units of measurement are included in thisstandard.1.3 The following applies to all specified limits in thisstandard:for purposes of determining conformance with thisstandard,an observed value or a calculated value shall berounded off“to the nearest unit”in the last right-hand digitused
4、 in expressing the specification limit,in accordance withthe rounding-off method of Practice E29.1.4 For hazard information and guidance,see the suppliersMaterial Safety Data Sheet.1.5 This international standard was developed in accor-dance with internationally recognized principles on standard-iza
5、tion established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:3D268 Guide for Sampling and Testing Volatile Solvents and
6、Chemical Intermediates for Use in Paint and RelatedCoatings and MaterialD1078 Test Method for Distillation Range of Volatile Or-ganic LiquidsD1209 Test Method for Color of Clear Liquids(Platinum-Cobalt Scale)D1353 Test Method for Nonvolatile Matter in Volatile Sol-vents for Use in Paint,Varnish,Lacq
7、uer,and RelatedProductsD1364 Test Method for Water in Volatile Solvents(KarlFischer Reagent Titration Method)D1613 Test Method for Acidity in Volatile Solvents andChemical Intermediates Used in Paint,Varnish,Lacquer,and Related ProductsD4052 Test Method for Density,Relative Density,and APIGravity of
8、 Liquids by Digital Density MeterD5386 Test Method for Color of Liquids Using TristimulusColorimetryE29 Practice for Using Significant Digits in Test Data toDetermine Conformance with SpecificationsE300 Practice for Sampling Industrial Chemicals2.2 U.S.Federal Specification:4PPP-C-2020 Chemicals,Liq
9、uid,Dry,and Paste:Packagingof3.Properties3.1 sec-butyl alcohol shall conform to the following require-ments:Apparent specific gravity:20/20 C0.807 to 0.809or25/25 C0.804 to 0.806Color,Pt-Co scale,maxA10Distillation range,760 mmHg,C as:Initial boiling point,min98.0Dry point,max101.0Nonvolatile matter
10、,max,mg/100 mL5Water,max,weight%0.5Acidity,as acetic acid,max,weight%0.002BAInstrumental Pt-Co color determined by Test Method D5386 has been shown tohave no statistically significant difference from Pt-Co color determined by TestMethod D1209.However,it is not known whether sec-butyl alcohol was par
11、t of thesample set included in the interlaboratory study.BEquivalent to 0.019 mg of KOH per gram of sample.4.Sampling4.1 The material shall be sampled in accordance withPractice E300.1This specification is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings,Materials,and Applic
12、ations and is the direct responsibilityD01.35 on Solvents,Plasticizers,and Chemical Intermediates.Current edition approved April 1,2019.Published April 2019.Originallyapproved in 1949.Last previous edition approved in 2011 as D1007 11.DOI:10.1520/D1007-11R19.2This compound is also known under the na
13、mes 2-butanol and secondarybutanol.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.4Available from Standardization
14、 Documents Order Desk,DODSSP,Bldg.4,SectionD,700RobbinsAve.,Philadelphia,PA19111-5098,http:/dodssp.daps.dla.mil.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally rec
15、ognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.1 5.Test Methods5.1 The properties enumerated in this specificatio
16、n shall bedetermined in accordance with the following ASTM methods:5.1.1 Apparent Specific GravityDetermine the apparentspecific gravity at 20 or 25 C by a convenient method that isaccurate to the third decimal place.See Guide D268 or TestMethod D4052.5.1.2 ColorTest Method D1209(see Note A in 3.1).5.1.3 Distillation RangeTest Method D1078 using a tem-perature measuring device having a range of 72 to 126 C anda resolution of 0.1 C.5.1.4 Nonvolatile MatterTest Method D1353.5.1.5 WaterTest Method
