收藏 分享(赏)

ASTM_F_2098_-_08.pdf

上传人:益****师 文档编号:190513 上传时间:2023-03-04 格式:PDF 页数:4 大小:149.23KB
下载 相关 举报
ASTM_F_2098_-_08.pdf_第1页
第1页 / 共4页
ASTM_F_2098_-_08.pdf_第2页
第2页 / 共4页
ASTM_F_2098_-_08.pdf_第3页
第3页 / 共4页
ASTM_F_2098_-_08.pdf_第4页
第4页 / 共4页
亲,该文档总共4页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation:F209808Standard Specification forStainless Steel Clamps for Securing SDR9 Cross-linkedPolyethylene(PEX)Tubing to Metal Insert and Plastic InsertFittings1,2This standard is issued under the fixed designation F2098;the number immediately following the designation indicates the year oforigi

2、nal adoption or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This specification covers stainless steel clamps for usewith four sizes

3、 of insert fittings that comply with F1807,andcross-linked polyethylene(PEX)plastic tubing that complieswith F876 or F877.These clamps are intended as an alternativeto the copper-alloy crimp-rings of Specifications F1807 orF2159 for use in 100 psi(689.5 kPa)cold-and hot-waterdistribution systems ope

4、rating at temperatures up to andincluding 180F(82C).Included are requirements formaterials,workmanship,dimensions and marking of the stain-less steel clamps;requirements for deforming the clamps;which apply to assemblies of PEX tubing and SpecificationsF1807 and F2159,insert fittings secured with de

5、formed clampsper this specification.1.2 The values stated in inch-pound units are to be regardedas the standard.The SI values stated in parentheses areprovided for information purposes.1.3This standard does not purport to address all of thesafety concerns,if any,associated with its use.It is theresp

6、onsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2.Referenced Documents2.1 ASTM Standards:3A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate,Sheet,and St

7、rip for PressureVessels and for General ApplicationsD618 Practice for Conditioning Plastics for TestingD1598 Test Method for Time-to-Failure of Plastic PipeUnder Constant Internal PressureD1599 Test Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe,Tubing,and FittingsD1600 Termin

8、ology forAbbreviated Terms Relating to Plas-ticsD2122 Test Method for Determining Dimensions of Ther-moplastic Pipe and FittingsE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsF412 Terminology Relating to Plastic Piping SystemsF876 Specification for Crosslinked Polyethylene(PEX)Tub-ingF

9、877 Specification for Crosslinked Polyethylene(PEX)Hot-and Cold-Water Distribution SystemsF1807 Specification for Metal Insert Fittings Utilizing aCopper Crimp Ring for SDR9 Cross-linked Polyethylene(PEX)Tubing and SDR9 Polyethylene of Raised Tem-perature(PE-RT)TubingF2159 Specification for Plastic

10、Insert Fittings Utilizing aCopper Crimp Ring for SDR9 Cross-linked Polyethylene(PEX)Tubing and SDR9 Polyethylene of Raised Tem-perature(PE-RT)Tubing3.Terminology3.1 Definitions are in accordance with Terminology F412and abbreviations are in accordance with Terminology D1600,unless otherwise indicate

11、d.4.Classification4.1 This specification covers one class of stainless steelclamps in four sizes suitable for securing PEX tubing thatmeets the requirements of Specifications F876 or F877 to insertfittings that meet the requirements of Specifications F1807 andF2159.5.Materials and Manufacture5.1 Cla

12、mpsClamps shall be made from material meetingthe requirements of Specification A240/A240M stainless steelUNS S304000.1This specification is under the jurisdiction of ASTM Committee F17 on PlasticPiping Systems and is the direct responsibility of Subcommittee F17.10 on Fittings.Current edition approv

13、ed March 1,2008.Published March 2008.Originallyapproved 2001.Last previous edition approved in 2004 as F2098041.DOI:10.1520/F2098-08.2The stainless steel clamp described in this standard is covered by a patent.Interested parties are invited to submit information regarding the identification of analt

14、ernative to this patented item toASTM Headquarters.Your comments will receivecareful consideration at a meeting of F17,which you may attend.3For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact ASTM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume in

15、formation,refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United States1 6.General Requirements6.1 The following sections of Specification F877 constitutea part of this specification.6.1.1

16、Requirements,6.1.2 Test Methods,and6.1.3 Retest and Rejection.6.2 In addition,when a section with a title identical to thatreferenced in 6.1 above,appears in this specification,itcontains additional requirements that supplement those appear-ing in Specification F877.6.3 GeneralAll performance tests shall be performed onassemblies of fittings,clamps and PEX tubing.Clamps shallmeet the material and dimensional requirements of this speci-fication.Metal insert fittings shall meet the material anddim

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 专业资料 > 国外标准

copyright@ 2008-2023 wnwk.com网站版权所有

经营许可证编号:浙ICP备2024059924号-2