1、Designation:D799122Standard Test Method forDetermining Aerobic Biodegradation of Plastics Buried inSandy Marine Sediment under Controlled LaboratoryConditions1This standard is issued under the fixed designation D7991;the number immediately following the designation indicates the year oforiginal adop
2、tion or,in the case of revision,the year of last revision.A number in parentheses indicates the year of last reapproval.Asuperscript epsilon()indicates an editorial change since the last revision or reapproval.1.Scope1.1 This test method determines the biodegradation level ofplastic materials expose
3、d to laboratory conditions that simulatethe environment found in the sandy tidal zone.1.2 The tidal zone,that is,the part of the coast affected bythe tides and movement of the waves,is the borderline betweensea and land,frequently a sandy area that is kept constantlydamp by the lapping of the waves.
4、Stony and rocky shorelinesalso exist.1.3 Plastic marine debris is frequently washed up in thishabitat where it must be removed in order to restore theoriginal landscape.1.4 It is of interest to know the biodegradation behavior ofplastics when exposed to conditions simulating this habitat,because thi
5、s information can help in predicting the time neededfor the biodegradation of the litter.1.5 Biodegradation is determined by measuring the CO2evolved by the plastic material when exposed to a sedimentkept wet with salt-water in a reactor,to simulate the tidal zone.1.6 Marine fresh-water habitats(for
6、 example,those found inbrackish waters and estuaries)are not considered by thisstandard.1.7 Reports shall clearly state the percentage of net CO2generation for both the test and reference samples at thecompletion of the test.Furthermore,in the laboratory reports,the results shall not be extrapolated
7、 beyond the actual durationof the test.NOTE1There is no known ISO equivalent to this standard.1.8 UnitsThe values stated in SI units are to be regardedas standard.No other units of measurement are included in thisstandard.1.9 This standard does not purport to address all of thesafety concerns,if any
8、,associated with its use.It is theresponsibility of the user of this standard to establish appro-priate safety,health,and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.10 This international standard was developed in accor-dance with internationally
9、 recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards,Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade(TBT)Committee.2.Referenced Documents2.1 ASTM Standards:2D5988 Test Method f
10、or Determining Aerobic Biodegrada-tion of Plastic Materials in Soil2.2 ISO Standards:3ISO 8245 Water quality Guidelines for the determination oftotal organic carbon(TOC)and dissolved organic carbon(DOC)3.Terminology3.1 Definitions:3.1.1 tidal zone,nthe part of the marine environment thatextends from
11、 the high tide line,which is rarely inundated withwater,to the low tide line,which is typically always coveredwith water.3.1.1.1 DiscussionSynonyms are:eulittoral zone,midlit-toral zone,mediolittoral zone,intertidal zone,foreshore.4.Summary of Test Method4.1 This test method consists of the followin
12、g:4.1.1 Selection of plastic material for the determination ofaerobic biodegradation in a controlled laboratory system.4.1.2 Obtaining sediment and seawater from the shoreline.1This test method is under the jurisdiction of ASTM Committee D20 on Plasticsand is the direct responsibility of Subcommitte
13、e D20.96 on EnvironmentallyDegradable Plastics and Biobased Products.Current edition approved May 1,2022.Published May 2022.Originallyapproved in 2015.Last previous edition approved in 2015 as D7991-15.DOI:10.1520/D799122.2For referenced ASTM standards,visit the ASTM website,www.astm.org,orcontact A
14、STM Customer Service at serviceastm.org.For Annual Book of ASTMStandards volume information,refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute(ANSI),25 W.43rd St.,4th Floor,New York,NY 10036,http:/www.ansi.org.Copyright ASTM Internat
15、ional,100 Barr Harbor Drive,PO Box C700,West Conshohocken,PA 19428-2959.United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards,Guides an
16、d Recommendations issued by the World Trade Organization Technical Barriers to Trade(TBT)Committee.14.1.3 Exposing the plastic material to the wet sedimentunder controlled conditions.4.1.4 Measuring CO2evolved as a function of time.4.1.5 Assessing the degree of biodegradation by determin-ing the percentage of organic carbon in the plastic material thatis converted to CO2during the duration of the test.Thispercentage represents the percentage of mineralization and willnot include the amount of ca
